Tecumseh Vector Carbs- Starving for Fuel - HobbyTalk
  
HobbyTalk Forum for Diecast Collectors, Modelers, Slot Cars, & Radio Control
Home Forums Photo Album RC TrackFinder Catalog Donation/HobbyTalk Supporter

Welcome to the HobbyTalk forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, view attachments, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us. Forgotten your password? Click here!

NOTE: Once you register and are logged in this welcome section will no longer be visible.

Go Back   HobbyTalk > Small Engine Repair > Small Engine Repair 4-Cycle
Register Classifieds Help/TOS Members List Calendar Mark Forums Read

Reply
 
Thread Tools
  #1  
Old 04-18-2011, 11:20 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Tecumseh Vector Carbs- Starving for Fuel

Hi Folks,

Just wondering if anyone else is having similar problems to mine when it comes to the Tecumseh Vector Carbs.

I worked on a YardMachines Rider with a 13.5 HP Tecumseh.
Engine was acting like it was starving for fuel. Replaced all new fuel lines, filter, and put on new Vector Bowl kit (Plastic Bowl assembly-basically the entire lower half of carb + new diaphram).

Unit ran fine as long as it was on level ground, but started to struggle under a load going uphill.
Eventually it would surge and sputter and die. Some attempts to restart worked, but eventually it failed to restart.
Had some luck spraying starter fluid in carb, but after it quickly burned off--No luck.
Checked Choke plate function and plate opens and closes properly.
Throttle and linkages are not binding and work properly as well.

Checked fuel line to ensure gravity flow wasn't hindered, steady flow all the way to carb. Pulled bowl off carb and hardly any gas was in the bowl.
I would expect the bowl to be somewhat full if I have a good fuel stream coming from the fuel line to the carb.

Almost seems like the needle sticks in the seat, restricting incoming fuel. (just my guess)

Just wondering why after installing new Bowl Kit why these symptoms occur. These Vectors seem to fail alot.

This unit used part #770639.(Carb Bowl Kit)

Engine is a Tecumseh OHV135-206904E

Last edited by Tamfan; 04-18-2011 at 11:29 PM.. Reason: additional info posted.
Reply With Quote
  #2  
Old 04-19-2011, 07:48 AM
jsouth jsouth is offline
Member

My Photos
 
Join Date: Jan 2008
Posts: 200
Try loosing your fuel cap,cap may not be venting causing a vacuum,and very little fuel flow.Hope this helps.

Jerry
Reply With Quote
  #3  
Old 04-19-2011, 09:10 AM
John Lolli John Lolli is offline
Member

My Photos
 
Join Date: Nov 2005
Posts: 117
The Vector engine used two different carbs Split and Married. The only way I can tell the difference is to remove the drain bowl screw. On the Married variety there is also a spring, main fuel jet, and o ring. The o ring over time flattens out and blocks the main jet. If you have a Married carb then try replacing the o ring. I have seen this on a few Vector engines that run poorly adn the o ring solved the problem.
Reply With Quote
  #4  
Old 04-19-2011, 10:31 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Thanks JS and JL.

I tried loosing the gas cap while I was on the service call (forgot to mention that), it had no effect.

I'll check the O-ring. This is a "Brand New" Bowl kit w/ a new diaphram. Unless it was defective, the total run time after install was less than 1 hour before the failure started.
It would be hard to believe the O-ring failed so quickly.
Reply With Quote
  #5  
Old 04-19-2011, 10:58 PM
30yearTech's Avatar
30yearTech 30yearTech is offline
HobbyTalk Supporter

My Photos
 
Join Date: Sep 2006
Location: Central Texas
Posts: 5,714
Is there an inline fuel filter? If so is it one specific to a gravity feed system. The wrong kind of fuel filter will sometimes cause fuel starvation.
__________________
Ya gotta know how it WORKS, before you can figure out why it WONT
Reply With Quote
  #6  
Old 04-21-2011, 04:07 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Quote:
Originally Posted by 30yearTech View Post
Is there an inline fuel filter? If so is it one specific to a gravity feed system. The wrong kind of fuel filter will sometimes cause fuel starvation.
Thanks 30Year, I'm going to try it with another filter.
Hope it makes a difference. I matched it to what was on it on the service call, which was the common small red filters that are on a ton of small riders with Tecumseh and Briggs. Some of them are red, some are white, like Briggs #394358.
Reply With Quote
  #7  
Old 06-03-2011, 05:18 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Vector Still acting up

Customer wanted a new carb.

Installed a new Vector carb on this unit and they had it for 3 weeks and are now reporting the same problem is occurring again--- spits, sputters and stalls on an incline.

Anyone got any ideas?
Reply With Quote
  #8  
Old 06-03-2011, 10:24 PM
geogrubb geogrubb is offline
Elder Statesman

My Photos
 
Join Date: Jul 2006
Location: Missouri
Posts: 1,600
Not trying to be real scientific or technical, however, on this incline, if the engine is gravity fed and in one direction of the incline the tank is below the carb, no fuel flows and depending upon the relationship of the carb float to the incline in the other direction the float will not drop far enough to let fuel in as it thinks the bowl is full. It may be as simple as they started mowing in a different direction. Newton and I ate from the same apple tree. Have a good one. Geo

Last edited by geogrubb; 06-03-2011 at 10:27 PM..
Reply With Quote
  #9  
Old 06-05-2011, 11:54 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Angry

Quote:
Originally Posted by geogrubb View Post
Not trying to be real scientific or technical, however, on this incline, if the engine is gravity fed and in one direction of the incline the tank is below the carb, no fuel flows and depending upon the relationship of the carb float to the incline in the other direction the float will not drop far enough to let fuel in as it thinks the bowl is full. It may be as simple as they started mowing in a different direction. Newton and I ate from the same apple tree. Have a good one. Geo
Thanks Geo, I considered that as well.

Here's where I'm at on this machine:

I put on a new fuel line without a filter (just to rule out a filter problem).
Once I conquer this machine, I'll re-install a filter again.

I checked the O-ring in the jet, it wasn't flattened out, but I replaced it anyway to rule it out.

I can get the engine to run on level ground for 2-3 minutes and then it sputters out and dies.

Once I move throttle to Full Choke, I can restart it with no problem.
It does get finicky when restarting and it will stay running as long as I play with the throttle cable, engaging the choke back and forth.
It still seems to "want" to run rich.

BUT....
if I spray starter fluid in the throat, Fully choke it, it will start. Then I can back off the choke to open the choke plate wide open, and it will run 2-3 mins and die again.

Now about the Fuel Tank Cap:
I ran all the above mentioned test with the fuel cap off.
I should know this, but I'll ask anyway,... is this an acceptable way to rule out a clogged fuel cap?

I'm still stumped, but determined to get it solved.

Thanks Guys!
Reply With Quote
  #10  
Old 08-12-2011, 07:41 AM
John Lolli John Lolli is offline
Member

My Photos
 
Join Date: Nov 2005
Posts: 117
Have you solved this problem yet ???
Reply With Quote
  #11  
Old 08-14-2011, 11:35 PM
Tamfan's Avatar
Tamfan Tamfan is offline
Member

My Photos
 
Join Date: Jun 2010
Location: Memphis Metro Area, TN
Posts: 78
Quote:
Originally Posted by John Lolli View Post
Have you solved this problem yet ???
John,

I tried replacing the O-ring on the new carb and still had the same problem.
I went back and took the original carb and replaced the O-ring for the second time and it performed well with no hic-ups.

Thanks for your advice!
Reply With Quote
  #12  
Old 08-15-2011, 08:01 AM
John Lolli John Lolli is offline
Member

My Photos
 
Join Date: Nov 2005
Posts: 117
One thing I have learned regarding these vector carbs is that you have to really push down on the red plastic jet when you seat it. I has to sit just a little below the thick gasket that is between the upper and lower halves. Sounds like you got it squared away -- thanks for the response.
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Featured Sponsor

You Can Sponsor
A HobbyTalk Forum


HobbyTalk® Sponsors
Diecast
CScollectibles
Collectables Corner
DieCast Alley
Global Diecast Direct
Milezone
Mini-Motors Inc
Scoomer
The Toy Peddler
Toy Car Aution
Models
MegaHobby
Modeler’s Brand
ParaGrafix Modeling Systems
Radio Control
BeachRC.com
B-Fast RC
Dirt Cheap RC
Discount RC Tires
Irrgang Racing Service
Lefthander RC
MaxAmps.com
RCTV Live
SMC Racing
Speedzone
Thunder Racing
Tekin
Trend Times
TQ Racing
Windtunnel Racing
Slot Cars
AFX Racing
Scoomer
Slot Magazine
Sponsored Events

Become a
HobbyTalk® Supporter

Advertise on HobbyTalk®



Powered by vBulletin®
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
All times are GMT -4. The time now is 04:12 AM.
HobbyTalk® is a Registered Trademark of HobbyTalk Ltd.
All other logos and trademarks on this site are property of their respective owner.
Copyright (c) 1997-2012 HobbyTalk Ltd. No use without permission.
Advertising positioning by Digital Point