Poulan Pro Link PPB200 31cc engine gas line replacement - HobbyTalk
HobbyTalk Forum for Diecast Collectors, Modelers, Slot Cars, & Radio Control
Home Forums Photo Album RC TrackFinder Catalog Donation/HobbyTalk Supporter

Welcome to the HobbyTalk forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, view attachments, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us. Forgotten your password? Click here!

NOTE: Once you register and are logged in this welcome section will no longer be visible.

Go Back   HobbyTalk > Small Engine Repair > Small Engine Repair 2-Cycle
Register Classifieds Help/TOS Members List Calendar Mark Forums Read

Thread Tools
Old 06-16-2010, 12:36 AM
BillieMc BillieMc is offline

My Photos
Join Date: Jun 2010
Location: Claremore, OK
Posts: 3
Poulan Pro Link PPB200 31cc engine gas line replacement

Poulan Pro Line Weedeater PPB200 31cc engine. I had to replace the primer bulb and gas lines. Gas lines weren't there so have no idea how to put them on. I tried and it runs great for about 30 seconds then idles down until it dies. The parts store gave me 2 sizes of gas line, the primer bulb and gas filter. I put the gas filter on the large line in the tank. I need to know how to run the gas lines and which sizes to use where.
The prime bulb unit has a short nibble and a long nibble.
The carburator has a "L" shape nipple and a straight nibble.
Then there's two holes in the bottom of the gas tank for gas lines.

Both new lines are yellow colored but two sizes

Any help would be appreicated.
Reply With Quote
Sponsored Links
Old 06-16-2010, 05:43 AM
glenjudy glenjudy is offline

My Photos
Join Date: Aug 2006
Location: Northeast OK
Posts: 422
Here goes,
The smaller line will go on the smaller straight fitting on the carb to the corner of the tank, it has the fuel filter on it in the tank.

the, a little bit bigger line, will go on the L shaped fitting on the carb to the short post on the air purge bulb, the same size line will then go from the longer post on the air purge bulb up into the tank about 1/2 inch.
Claremore, OK
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Featured Sponsor
You Can Sponsor
A HobbyTalk Forum

HobbyTalk® Sponsors
Collectables Corner
DieCast Alley
Global Diecast Direct
Mini-Motors Inc
The Toy Peddler
Toy Car Aution
Modeler’s Brand
ParaGrafix Modeling Systems
TenaControls, LLC
Radio Control
B-Fast RC
Dirt Cheap RC
Discount RC Tires
Irrgang Racing Service
Lefthander RC
P1 Hobbies
SMC Racing
Thunder Racing
Trend Times
TQ Racing
Windtunnel Racing
Slot Cars
AFX Racing
Slot Magazine
Sponsored Events

Become a
HobbyTalk® Supporter

Advertise on HobbyTalk®

Powered by vBulletin®
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
All times are GMT -4. The time now is 05:01 AM.
HobbyTalk® is a Registered Trademark of HobbyTalk Ltd.
All other logos and trademarks on this site are property of their respective owner.
Advertising positioning by Digital Point