snowblower motor starts then dies after a couple seconds - HobbyTalk
  
HobbyTalk Forum for Diecast Collectors, Modelers, Slot Cars, & Radio Control
Home Forums Photo Album RC TrackFinder Catalog Donation/HobbyTalk Supporter

Welcome to the HobbyTalk forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, view attachments, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us. Forgotten your password? Click here!

NOTE: Once you register and are logged in this welcome section will no longer be visible.

Go Back   HobbyTalk > Small Engine Repair > Small Engine Repair 4-Cycle
Register Classifieds Help/TOS Members List Calendar Mark Forums Read

Reply
 
Thread Tools
  #1  
Old 02-18-2007, 12:12 PM
fhk2020 fhk2020 is offline
Member

My Photos
 
Join Date: Feb 2007
Posts: 4
Question snowblower motor starts then dies after a couple seconds

I have a 10 hp tecumseh on a snapper blower and the motor starts then dies after a couple seconds. Any help would be greatly appreciated. I put in new fuel. It should be noted that I have to push the primer button MANY times to get it to start at all - but then it dies pretty quick. I took the primer button off and it appears to have no holes??? I cleaned the carb ( i'm no expert - could I have not done a thorough cleaning??? ). The bowl fills up with gas - although the plug does not seem to get wet - so i don't think it's a fouling problem.
Reply With Quote
  #2  
Old 02-18-2007, 04:05 PM
repair_guy's Avatar
repair_guy repair_guy is offline
Member

My Photos
 
Join Date: May 2004
Location: Bessemer,Alabama.USA.
Posts: 151
Losen the fuel tank cap and try it.If it runs then the vent hole is cloged in it.
If not take the bowl nut back off and clean the tiny hole between the threads,also make the emerion tubes are clear.
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Featured Sponsor

You Can Sponsor
A HobbyTalk Forum


HobbyTalk® Sponsors
Diecast
CScollectibles
Collectables Corner
DieCast Alley
Global Diecast Direct
Milezone
Mini-Motors Inc
Scoomer
The Toy Peddler
Toy Car Aution
Models
MegaHobby
Modeler’s Brand
ParaGrafix Modeling Systems
Radio Control
BeachRC.com
B-Fast RC
Dirt Cheap RC
Discount RC Tires
Irrgang Racing Service
Lefthander RC
MaxAmps.com
RCTV Live
SMC Racing
Speedzone
Thunder Racing
Tekin
Trend Times
TQ Racing
Windtunnel Racing
Slot Cars
AFX Racing
Scoomer
Slot Magazine
Sponsored Events

Become a
HobbyTalk® Supporter

Advertise on HobbyTalk®



Powered by vBulletin®
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
All times are GMT -4. The time now is 08:39 AM.
HobbyTalk® is a Registered Trademark of HobbyTalk Ltd.
All other logos and trademarks on this site are property of their respective owner.
Copyright (c) 1997-2012 HobbyTalk Ltd. No use without permission.