Removing an impeller from an MTD Chipper Shredder - HobbyTalk
  
HobbyTalk Forum for Diecast Collectors, Modelers, Slot Cars, & Radio Control
Home Forums Photo Album RC TrackFinder Catalog Donation/HobbyTalk Supporter

Welcome to the HobbyTalk forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, view attachments, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us. Forgotten your password? Click here!

NOTE: Once you register and are logged in this welcome section will no longer be visible.

Go Back   HobbyTalk > Small Engine Repair > Small Engine Repair 4-Cycle
Register Classifieds Help/TOS Members List Calendar Mark Forums Read

Reply
 
Thread Tools
  #1  
Old 06-11-2006, 03:18 PM
phoneman phoneman is offline
New Member

My Photos
 
Join Date: Jun 2006
Posts: 2
Removing an impeller from an MTD Chipper Shredder

I am trying to remove the impeller from my MTD chipper shredder model # 244-648B000 with a Tecumsah 8 hp engine. I have everything removed but the impeller. I feel like Egger trying to open the box of diamonds in Men in Black. I'm assuming this is a keyed crankshaft. I've tried everything I can think of. Any help would be appreciated.
Reply With Quote
  #2  
Old 06-12-2006, 11:34 AM
Munkey Munkey is offline
Member

My Photos
 
Join Date: Jun 2006
Posts: 27
Are there any puller bolt holes in the impeller? If not, a good dose of WD-40 and a rubber hammer might shift it.
Reply With Quote
  #3  
Old 06-18-2006, 07:30 AM
phoneman phoneman is offline
New Member

My Photos
 
Join Date: Jun 2006
Posts: 2
I've tried a pull with no luck....I'll try the WD-40 Thanks
Reply With Quote
  #4  
Old 06-19-2006, 09:00 PM
Rpeters123 Rpeters123 is offline
Member

My Photos
 
Join Date: Oct 2005
Location: Nashua NH
Posts: 93
Thumbs up Try candle wax to loosen

Get a propane torch heat up impeller not shaft. Take a candle made of parafin wax and it will get sucked inside the hole when held near shaft.Then use a steel hammer hit in both directions.Have fun watch the fingers!
Reply With Quote
  #5  
Old 06-20-2006, 01:04 AM
bugman's Avatar
bugman bugman is offline
HobbyTalk Pro

My Photos
 
Join Date: Aug 2004
Location: NC
Posts: 3,241
Or PB blaster....... wd-40 wasn't cut out to do anything more then what it was actually made for.... a water displacer (WD)
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Featured Sponsor
Buy RC Cars 
from AirsoftRC.com
---------------
Remote Control Cars and The Best Toys On Sale at Trend Times Toy Store

---------------

You Can Sponsor
A HobbyTalk Forum


HobbyTalk® Sponsors
Diecast
CScollectibles
DieCast Alley
Global Diecast Direct
Milezone
Mini-Motors Inc
Scoomer
The Toy Peddler
Toy Car Aution
Models
MegaHobby
Modeler’s Brand
ParaGrafix Modeling Systems
Radio Control
AirsoftRC.com
BeachRC.com
B-Fast RC
Dirt Cheap RC
Discount RC Tires
Irrgang Racing Service
Lefthander RC
MaxAmps.com
RCTV Live
SMC Racing
Speedzone
Thunder Racing
Tekin
Trend Times
TQ Racing
Windtunnel Racing
Slot Cars
AFX Racing
Scoomer
Slot Magazine
Sponsored Events

Become a
HobbyTalk® Supporter

Advertise on HobbyTalk®



Powered by vBulletin®
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
All times are GMT -4. The time now is 07:46 AM.
HobbyTalk® is a Registered Trademark of HobbyTalk Ltd.
All other logos and trademarks on this site are property of their respective owner.
Copyright (c) 1997-2012 HobbyTalk Ltd. No use without permission.