is anyone running a Titanium axle in there sprint car? i read through the rule book and see nothing that says you cant please let me know if anyone knows otherwise thanks Brad

Hi:Brad
They are perfectly legal and terrifically expensive and I want them.
Also the next race or fun day at Milestone will be much different trust me !!!
Bill

what would anyone be willing to pay for a TI axle if i was to get stock? i can get hollow or bar stock lmk Brad

Touch base with Fred Murry.

I have two axles that I purchased through Fred. I don't think bar stock will work as it comes stock. I think it needs to be taken down a couple of tenths (.0001-.0005 at worst case). I don't think it matters whether its solid bar stock or tube stock.

Titanium is INSANELY expensive in the raw stock form. I checked on prices through our procurement department and an 18" piece would have been well over $75 cost.

All that said, I think Fred was charging $60 for his pieces, if I remember right.

Joe Brooks
:thumbsup:

is anyone running a Titanium axle in there sprint car? i read through the rule book and see nothing that says you cant please let me know if anyone knows otherwise thanks Brad

Brad:
I have been running and suppling titanium axles for a few years now. I would not run anything but. I use them on the front and the rear. I have yet to bend one and my car has been thru some major crashes. :wave: :woohoo:
Fred Murry

Brad: They are expensive but well worth the money.Fred

look forward to seeing them

Brad:
I have been running and suppling titanium axles for a few years now. I would not run anything but. I use them on the front and the rear. I have yet to bend one and my car has been thru some major crashes. :wave: :woohoo:
Fred Murry
Fred do you make them for the GN cars?

Fred do you make them for the GN cars?

Jeff:
I have made somefor GN. I may have some in the shop. What length do you want?
Fred

Fred, How much for a front and rear axle for a WCM ? What kind of ends do you run on the front axle? Mike

Fred, How much for a front and rear axle for a WCM ? What kind of ends do you run on the front axle? Mike

Mike:
I will get a fresh quote on titanium on Wed as the prices go up and down. Mostly up. Last rear axles I sold were $65.. for an 18 inch wide axle, solid NOT tube. Front axle is 12 inch wide and I use a modified Hughes clamp on the end instead of the taperd ones from WCM. These will accept the stock WCM spindles new or old style. I also use clamps to hold the servo mount and slider. NO holes in the axle to weaken it. If you want photos email me at FMurry8995@aol.com and I will send some your way.

Fred

Jeff:
I have made somefor GN. I may have some in the shop. What length do you want?
Fred
Fred,
I will measure and let you know.
Thanks

Hey Fred, I sent you a email, don't know if it went through? michael546007@yahoo.com

Mike

Mike working on photos now.
Fred

still looking for a TI rear axle

Send me a e-mail ts.hughes@verizon.net
Tom

Just wanted to say thanks to Fred for the awsome axles. If anybody's looking for a set , get a hold of Fred you will not be disappointed . Thanks again
Mike

Just wanted to say thanks to Fred for the awsome axles. If anybody's looking for a set , get a hold of Fred you will not be disappointed . Thanks again
Mike
Hey Mike you got that thing on already?Im ready to put it thru the paces this year to find out how industructable that car is!! LOL :woohoo:

Mike:
I will get a fresh quote on titanium on Wed as the prices go up and down. Mostly up. Last rear axles I sold were $65.. for an 18 inch wide axle, solid NOT tube. Front axle is 12 inch wide and I use a modified Hughes clamp on the end instead of the taperd ones from WCM. These will accept the stock WCM spindles new or old style. I also use clamps to hold the servo mount and slider. NO holes in the axle to weaken it. If you want photos email me at FMurry8995@aol.com and I will send some your way.

Fred
heck mike you already got your axles i'm still waiting for a price!!!... all i ever heard was how expensive they were but well worth the money...

hey tom got my axle thanks Brad

It's just about ready for testing. I thinking about letting Gerald race it . He's use to rubbing and racing those GN's .

heck mike you already got your axles i'm still waiting for a price!!!... all i ever heard was how expensive they were but well worth the money...
Email Fred again , he's been real busy. Be sure and tell him what car it's for.

heck mike you already got your axles i'm still waiting for a price!!!... all i ever heard was how expensive they were but well worth the money...
Sorry. You have PM.
Fred :o Like the little guy I was sleeping. :o :(

Fred, this is Lance. PM me a price for 4 axles. 3 for a pro1 and 1 for a WCM if there is a difference.

Thanks