Hi im trying to add .330 to the end of a battery tray what can i use to keep it attatched .330 is not much it will have little to no weight on it trhanks :thumbsup:

maybe just try adding a peice of lexan. have it a bit longer then the graphite os it extends out. that should be good id think.

595

lexan or try thick C.A glue

glue!

Thick CA or Epoxy. Lay it flat on a table between two sheets of waxed paper and put some weight on it overnight while it cures.

thanks

Shoe Goo is best. it stay's a little flexable so it wont break off when it gets hit you can find it at your local hobby shop.

Hi, I am new in the forum and I need a hand.
A carbon anode of a desilvering unit has broken in two halves, which cement or glue must I use to join it?
I hope I could find a solution with your help.
regards

Hi, I am new in the forum and I need a hand.
A carbon anode of a desilvering unit has broken in two halves, which cement or glue must I use to join it?
I hope I could find a solution with your help.
regards

and i am guessing you need to replace the kanibler pin on your johnson mechanism and then re-attach it to your flux capacitor...... lol

my head hurts! going to sniff some glue now!

What Kind Of Glue You Sniffin Elmers?
Never Mind Thats The Kind You Eat.
Think I Ate To Much

Hi, I am new in the forum and I need a hand.
A carbon anode of a desilvering unit has broken in two halves, which cement or glue must I use to join it?
I hope I could find a solution with your help.
regards

Most likely the anode your dealing with has a ceramic mix base so most any cyanocrylate ( CA ) glue should work, I prefer the Loctite brand gel it leaves less flash and residue.

Most likely the anode your dealing with has a ceramic mix base so most any cyanocrylate ( CA ) glue should work, I prefer the Loctite brand gel it leaves less flash and residue.

Problem is that the CA will probably act as an insulator film between the 2 carbon parts. I don't think CA is a good electrical conductor material.

Martin Paradis

Thank very much for your aid FL Flash and you rhodopsine.
I have found a suitable glue, it is the Graphi-Bond 551-RN of AREMCO.
Doughboy, наверно ты такой валтум как и себе представляешь, also my english is not so good...

Doughboy, наверно ты такой валтум как и себе представляешь, also my english is not so good...
Doughboy- I don't speak Russian,but I'd say you just got pwned! LOL

my head hurts! going to sniff some glue now!
Kat = Billy Madison of the rc world:wave:

Problem is that the CA will probably act as an insulator film between the 2 carbon parts. I don't think CA is a good electrical conductor material.

Martin Paradis

Good point did'nt think of that? Hopefully what he found will work. Kinda curious why he doesent just replace the anode?

I,m real curious as to what his comment was to Doughboy???

Hi, I am new in the forum and I need a hand.
A carbon anode of a desilvering unit has broken in two halves, which cement or glue must I use to join it?
I hope I could find a solution with your help.
regards

True, CA's or epoxy will bond the anode, but the pH of the fixer flowing around the repair will erode the bond in no time flat, plus it will kill the elecctrical current to that anode, hurting your desilvering effecincey. Your best bet is to get a new anode...Sounds like you may need to replace them all.

Not to turn a how to bond a graphite thread into a silver recovery thread...

http://www.clipartguide.com/_named_clipart_images/0060-0806-2805-2144_Boy_Fishing_clipart_image.jpg